T 1949/09 26-09-2012

1. The appeal is admissible.

Preliminary procedural remarks in respect of the late filed material

2. Pursuant to Article 114(2) EPC the EPO may disregard facts and evidence not submitted in due time by the parties. As far as the appeal procedure is concerned, the Rules of Procedure of the Boards of Appeal (RPBA) give the general directions as to the way in which the Boards of Appeal have to exercise their power to admit or disregard the material filed at different stages of the appeal proceedings.

2.1 Article 12 delineates the basis of the appeal proceedings, providing that the appeal file should contain one comprehensive submission from each party. The purpose of this provision is that the exchange of the grounds and the reply should effect a defined and controlled initial phase of proceedings providing a moment in time fixed by the rules when a party's case is deemed to be complete, any further material submitted being, in the terms of Article 13 RPBA, an amendment to the party's case.

2.2 It is commonplace that amendments to a party's case filed in response to new objections raised by the other party or by the Board, are deemed to be filed in due time within the meaning of Article 114(2) EPC itself.

2.3 As to the other amendments (which cannot be deemed to be filed in due time), it is in the Board's discretion to evaluate their admissibility in the light of several criteria, the most common being listed in Article 13(1) RPBA: the complexity of the new subject-matter submitted, the current state of the proceedings and the need for procedural economy.

2.4 Finally, after oral proceedings have been arranged, an additional criterion has to be taken into account: the other party and the Board should be capable of dealing with the new issue without any adjournment of the oral proceedings (Article 13(3) RPBA).

2.5 These principles apply in the following paragraphs.

Admissibility of the declaration of the inventor

3. The declaration filed with letter of 12 September 2012 includes some tests performed to assay the mechanical strength of some catalysts (section 3 of the declaration) and a review of the content of document D6 (section 4 of the declaration).

3.1 In the light of the preliminary remarks, the Board notices that the tests included in the declaration cannot be deemed to be filed in due time, because they cannot be seen as a reaction to a new situation which was not already present at the time in which the grounds of appeal were filed, as the lack of experimental tests which would confirm an advantage of the specific catalyst was already a crucial point of the decision (see point IV, above), or at the latest after the respondent filed the letter of reply to the statement of grounds, in which a clear position was taken on the tests filed with that statement.

3.2 The only justification put forward for the late filing, namely the time needed to have the tests authorised and performed, cannot justify their filing almost three years after the grounds of appeal, more than two years after the reply of the respondent and only 15 days before the convened oral proceedings, all the more as the appellant never informed the Board of any difficulty in providing further evidence, nor requested additional time to prepare such evidence.

3.3 Apart from the unjustified late filing, the tests raise a number of questions about their significance, which could not be answered without an adjournment of the proceedings, including in particular the question whether the values of the mechanical strength depend only on the differences between the production method in D1 and in the opposed patent (in particular co-precipitation of chromium and aluminium hydroxides and formation of a catalyst in amorphous form) or on other parameters of the compared catalysts which do not appear in the claims (e.g. their particle size distribution) or on other features of the method of production which are present in other examples of D1, but do not form part of the tests (e.g. the presence of a calcination step as in examples 8 to 10 of D1).

3.4 Finally, Article 15(3) RPBA, which provides that the Board is not obliged to delay any step in the proceedings, including its decision, by reason only of the absence at the oral proceedings of any party, does not go so far as to nullify Article 113(1) EPC. On that basis, the respondent, which chose not to attend the oral proceedings, can rely on the procedural provisions mentioned above, namely that the decision would be made on the basis of the written case in the meaning of Article 12 RPBA and that no significant amendment of the case would be admitted which would go beyond what is foreseen by Article 13 RPBA (see also T 1621/09, unpublished, points 41 to 44).

3.5 For these reasons, the Board on application of the RPBA does not admit the tests included in the declaration filed with letter of 12 September 2012 into the proceedings (section 3 of the declaration).

3.6 On the contrary, the review of the content of document D6, which is based on the documents itself and on arguments which were already in the proceedings, (section 4 of the declaration) does not pose any problem with regard to admissibility and is therefore admitted into the proceedings.

Admissibility of D7 to D11

4. The contention that documents D7 to D11 were ipso facto part of the appeal proceedings only because they were mentioned in the description cannot be followed by the Board for the following reasons.

4.1 First of all, such a contention is inconsistent with Article 12 RPBA: to be part of the proceedings and play an active role for a new argumentation the documents should have been singled out in the written submissions as being of possible relevance at some point in time. Having been introduced at the oral proceedings before the Board without any previous indication, they are late filed and subject to a discretionary decision on their admissibility.

4.2 This approach is consistent with the case law (Case Law of the Boards of Appeal, VI edition 2010, VII.C.1.7), according to which a document considered during the examination procedure is not automatically scrutinised in opposition or opposition appeal proceedings, even it is quoted and acknowledged in the contested patent. Only the document cited and acknowledged in the description of the contested patent as the closest prior art and on the basis of which the technical problem in the description was formulated remains an exception and forms directly part of the opposition or opposition appeal proceedings.

4.3 Documents D7 to D11, although cited in the specification of the patent in suit, had been merely acknowledged as conventional background art therein (paragraphs [0009] to [0011] and [0013] in the patent) and were not considered in the patent as essential or as the closest prior art and the starting point of the claimed invention.

4.4 The appellant did not provide any justification of their late filing and did not present any of those documents as more relevant than the documents on file, as, in its arguments, D1 remained the closest prior art and none of D7 to D11 was relevant for the analysis of the obviousness of the solution (they were only used as supporting evidence for the acknowledgement of an effect).

4.5 Moreover, the respondent absent at the oral proceedings (as already indicated above, see point 3.4) and relying on the rules of procedure, could not have expected a new line of argumentation based on these documents and never announced in the written phase of the proceedings, which could have changed the analysis of the case and its counterarguments.

4.6 Therefore, pursuant to Article 13(1) and (3) RPBA the Board considers it appropriate not to admit documents D7 to D11 into the proceedings.

Main request - inventive step

5. Closest prior art

5.1 Document D1 has been considered as the closest prior art both in the appealed decision and in the arguments of the parties. The Board sees no reason to choose a different starting point.

5.2 D1 relates to an improved fluorination catalyst and to a process for the production of fluorinated hydrocarbons by the catalysed reaction of hydrocarbons or halogenated hydrocarbons with hydrogen fluoride (page 2, lines 1 to 3). In particular, it discloses a two-step process for the production of 1,1,1,2-tetrafluoroethane from trichloroethylene, in which the first stage is the vapour-phase fluorination of trichloroethylene with hydrogen fluoride (page 4, lines 35 to 38) and the second stage is the preparation of 1,1,1,2-tetrafluoroethane by reaction of 1-chloro-2,2,2-trifluoroethane with hydrogen fluoride (page 4, lines 31 to 33). In both stages use is made of the same promoted catalyst (page 4, lines 38 to 39).

5.3 The promoted catalyst of D1 is a chromium containing catalyst which comprises an activity-promoting amount of zinc or a compound of zinc (claim 1; page 2, lines 20 to 21). It preferably contains chromium in the form of chromia, halogenated chromia or chromium oxyfluoride (page 2, lines 30 to 31) and may comprise metal oxides, halogenated metal oxides or metal oxyfluorides other than those based on chromium, including e.g. alumina as metal oxide (page 2, lines 35 to 40), so that the chromium containing catalyst may comprise an activity promoting amount of zinc or a compound of zinc in and/or on a mixed metal oxide support, such as chromia/alumina (page 2, lines 42 to 46). The catalyst may be prepared among other methods by impregnation of a chromia, halogenated chromia or chromium oxyhalide with a water soluble salt of zinc or by co-precipitation of the hydroxides of the promoter and chromium with subsequent conversion to the oxides (page 3, lines 23 to 29).

5.4 Even if D1 mentions catalysts with the same constituents as the catalyst used in the process of claim 1 of the main request, namely chromium oxide, aluminium oxide and zinc as a promoter, and impregnation and co-precipitation are given as possible process steps for some of the embodiments, none of the embodiments of D1 refers to co-precipitation of Cr2O3 and Al2O3 to give an amorphous mixed oxide precatalyst which is then impregnated with a zinc compound and the respondent has not provided any evidence that the result of any of the embodiments of D1 should necessarily be a catalyst based on co-precipitated Cr2O3/Al2O3 in amorphous form. Under such circumstances, it cannot be acknowledged that D1 discloses a catalyst as the one used in the process of claim 1 of the main request.

5.5 The general description of D1 mentions typical contact times for the process reaction steps (page 5, lines 5 to 14). However, no sufficient information is given in the general part of D1 to make it possible to compute the ratio W/F (ratio of catalyst to feed in g.h/mole, paragraph [0024] of the patent). The same holds for the examples of D1, where the quantity of catalyst and the contact time are given (see e.g. examples 1 to 5, page 5, lines 36-40), but no value of the feed flow rate is available, so that the ratio W/F remains unknown.

6. Problem solved

6.1 According to the patent, it is the object of the invention to provide a process for the preparation of HFC-134a by the fluorination of trichloroethylene with a catalyst which achieves high selectivity and possesses enough crushing strength for use under pressure (paragraphs [0016]-[0018]).

6.2 Since D1 concerns the same process and addresses similar issues, it needs to be analysed whether the evidence on file makes it possible to acknowledge the presence of effects or improvements in the relevant properties with respect to the process of D1.

6.3 As far as the first reaction step of the process is concerned, namely the fluorination of trichloroethylene to 2-chloro-1,1,1-trifluoroethane, the Board cannot acknowledge that it has been credibly shown that an improvement in conversion and selectivity is obtained by means of the replacement of the catalysts of D1 with the catalyst used in the process of claim 1.

6.3.1 It is indeed true that in example 7 of D1 a conversion of 40.9% of trichloroethylene to 2-chloro-1,1,1-trifluoroethane is obtained (see page 6, lines 25 to 31 of D1), while in example 1 in the patent in suit (table in paragraph [0059]) catalyst B obtains a conversion of trichloroethylene of 96.5% and a selectivity for 2-chloro-1,1,1-trifluoroethane of 97.5%, as underlined by the appellant.

6.3.2 However, these results are obtained for different reactors working under different operating condition, so that it cannot be concluded whether the large differences in conversion and selectivity are related to the catalyst or to the reactor and its operating conditions.

6.3.3 In this respect it is noted that the use of chromia under the conditions of example 7 of D1 leads to a conversion of trichloroethylene to 2-chloro-1,1,1-trifluoroethane of 26.7% (page 6, line 31 of D1), while the use of chromia under the conditions of example 1 of the patent in suit (table in paragraph [0059], last column) leads to a conversion of trichloroethylene of 96% and a selectivity for 2-chloro-1,1,1-trifluoroethane of 97.5% (i.e. to results very similar to those of the catalyst used in the claim). These very different results which are obtained with the same material as catalyst make it clear that the influence of the reactor and of the operating conditions is very relevant and that a direct comparison between the results of example 7 of D1 and example 1 of the patent is suit is not appropriate to establish the effect of the choice of a different catalyst on the conversion and selectivity of the first reaction step.

6.3.4 This analysis confirms that the data on file do not make possible a reliable comparison between the performance of step (a) conducted with a catalyst according to D1 and the performance of the same step with the catalyst used in the patent in suit. In the absence of such a direct comparison it cannot be concluded whether an improvement in conversion and selectivity is obtained or not.

6.4 With regard to step (b) of the process of claim 1, namely the fluorination of a product containing 2-chloro-1,1,1-trifluoroethane to 1,1,1,2-tetrafluoroethane, the appellant has provided with the statement of grounds experimental data which are meant to reproduce example 5 of the patent in suit by replacing the catalyst used in the patent with some catalysts according to some examples of D1.

6.4.1 The data in example 5 of the patent in suit are according to the following table (paragraph [0063] of the patent):

| Catalyst | | Catalyst-B | |

| | | | |

| | | | |

|Reaction temp. | 360 | 360 | 360 |

|ºC | | | |

| | | | |

|Mole ratio, HF/| 8 | 6 | 6 |

|HCFC-133a | | | |

| | | | |

|Pressure, psig | 70 | 70 | 70 |

| | | | |

| | | | |

|W/F, g.h/mole | 100 | 70 | 50 |

| | | | |

| | | | |

|Conversion of H| 24.0 | 22.0 | 14.4 |

|CFC-133a, % | | | |

| | | | |

|Selectivity for| 96.0 | 88.2 | 84.5 |

|HFC-134a, % | | | |

| | | | |

6.4.2 The data provided by the appellant with the statement of grounds refer to the tests carried out on 3 catalysts of D1, namely catalysts prepared according to the procedure of examples 1, 3 and 15 of D1 in the conditions of example 5 of the patent in suit, and are reproduced in the following table (page 3 of the statement of grounds):

FORMULA/TABLE/GRAPHIC

6.4.3 These data show that catalysts 1 and 3 according to D1 provide sometimes comparable and often better conversion and selectivity than the catalyst used in the process of claim 1, while catalyst 15 has lower conversion values, but at times better selectivity.

6.4.4 These data cannot therefore support the view that the use of a catalyst according to the patent in suit in the process of claim 1 provides better values of conversion and selectivity in step (b) of the claimed process.

6.4.5 In this context it is relevant to note that the argument of the appellant that these tests would discourage the skilled person to use a catalyst with aluminium, chromium and zinc because of the worse results of catalyst 15 according to D1 is not relevant in the formulation of the problem solved by the process of claim 1 and can in any case not be followed, because these data were not available to the skilled person at the time of filing of the patent in suit.

6.4.6 Additionally it is noted that no comparative data are available with regard to examples 8 to 10 of D1, which were considered by the appellant as the best starting point for the analysis of inventive step in the line of arguments followed during the oral proceedings. Therefore, even if that approach were followed, no improvement in selectivity and conversion with respect to the use of those catalysts could be acknowledged.

6.5 With regard to the choice of the range 80-150 g.h/mole for the ratio W/F in step (b) of the process, reference is still made to the data in the table regarding example 5 of the patent in suit (point 6.4.1, above). While it is true that for the value within the range (100) conversion and selectivity are higher than in the other two cases (with W/F equal to 70 and 50 respectively), the W/F ratio is not the only parameter which has been changed in the tests, as the mole ratio HF/HCFC-133a is 8 when W/F is equal to 100 and 6 in the other cases, so that it cannot be concluded which is the difference that determines the improvement in conversion and selectivity. No other data are available to show an effect of the W/F ratio alone.

6.6 As to the operation under pressure, the appellant has provided data with the statement of ground showing that the catalysts according to D1 (examples 1, 3 and 15) as well as bulk chromia used in the pressure conditions of example 5 of the patent in suit exhibit poor mechanical strength with respect to the catalyst used in the patent in suit, so that a clogging phenomenon takes place (last four paragraphs on page 3 of the statement of grounds and results at the top of page 4).

6.7 As alleged advantages to which the patent proprietor merely refers without offering sufficient evidence, supported by any comparison with the closest prior art, cannot be taken into consideration in determining the problem effectively solved by the underlying invention (Case Law, supra, I.D.4.2), no improvement in conversion or selectivity can be acknowledged and that improvement cannot be part of the solved problem. It can only be acknowledged that the process of claim 1 can be operated under pressure (even if that feature is not part of the claim).

6.8 The problem solved by the process of granted claim 1 is therefore the provision of a further process for the preparation of HFC-134a by the fluorination of trichloroethylene which can be operated under pressure. In view of the preceding analysis this conclusion is independent of the specific embodiment of D1 which is taken as the starting point.

7. Obviousness

7.1 D6 belongs as D1 and the patent in suit to the field of fluorination catalysts for the fluorination of 2-chloro-1,1,1-trifluoroethane to 1,1,1,2-tetrafluoroethane (see abstract and first paragraph of the introduction of D6). Moreover, therein a base catalyst (co-precipitated Cr2O3/Al2O3) is chosen which meets the strength requirements for operation under pressure (last but one sentence of page 177).

7.2 In the experimental part the production of a number of catalysts is disclosed, including in particular the production of catalyst B which is obtained through impregnation of a co-precipitated Cr2O3/Al2O3 (using NH4OH followed by calcination) with zinc chloride (see page 178, Experimental, in particular sections 2.1.1 and 2.1.2). It was not contested by the appellant that catalyst B of D6 exactly corresponds to the catalyst used in the process of claim 1 of the main request, which is corroborated by the fact several of the authors of D6 are among the inventors of the patent in suit.

7.3 The skilled person looking for a further process for the preparation of HFC-134a by the fluorination of trichloroethylene which can be operated under pressure would therefore take into consideration the replacement of the catalysts of D1 with any of the catalysts proposed in D6, which address the same issues and contain the same main constituents, including in particular catalyst B.

7.4 Moreover, the skilled person would choose the appropriate operating conditions, including the quantity of catalyst and the flowrates of reactants as part of his normal skills.

7.5 In summary the skilled person addressing the posed problem would choose both any catalyst according to D6 (in particular catalyst B) and appropriate values of the W/F ratio without any inventive skills.

7.6 For these reasons the process of claim 1 of the main request does not involve an inventive step.

Auxiliary request - inventive step

8. The same arguments developed in detail for the process of claim 1 of the main request apply equally to the process of claim 1 of the auxiliary request for the reasons which follow.

8.1 The specification of the range for the Cr:Al molar ratio (1:3 to 1:10) for the catalyst used in the two-step process is not associated with any further effect or advantage with respect to the process of claim 1 of the main request. Indeed no evidence is available to show any relevance of the further feature and no different arguments have been submitted by the appellant in this respect.

8.2 Once the problem is formulated as above (point 6.8) and it is solved by means of the teaching of D6 (point 7.3), the additional feature is automatically included, as catalyst B of D6 has a Cr:Al molar ratio in the range 1:3 to 1:10 (as computed on the basis of the composition of catalyst B as given in Table 1 of D6). That point was initially contested by the appellant (point X (b), above), as a weight ratio was wrongly computed, but later accepted by both parties (points XI (c) and XII (b), above).

8.3 On that basis the process of claim 1 of the auxiliary request does not involve an inventive step.

Auxiliary requests 2 to 10 - admissibility

9. The Articles of the RPBA concerning the basis of the proceedings and the amendment of a party's case (Articles 12 and 13 RPBA), whose content has been summarised above (see points 2.1 to 2.4), make it clear that admission into the proceedings of late filed amendments will be the exception more than the rule, even more if the amendments are filed after arrangement of the oral proceedings.

9.1 There is nothing in the present case which could justify such exception with regard to the admissibility of auxiliary requests 2 to 10 filed with letter of 10 September 2012 (15 days before the oral proceedings) in view of the following facts:

(a) The grounds against the requests on file and the evidence used to support these grounds have remained the same as in the decision under appeal.

(b) The appellant has not provided any justification for the late filing.

(c) The appellant has not provided any reasons for the inventiveness of the main claims of those requests which go beyond the reasons already provided for the higher ranked requests.

(d) The amendments do not converge to a clearly identifiable amended form of the main claim, but introduce several alternative features into claim 1 of the patent as granted to be taken alone or in all possible combinations (see point VIII, above).

9.2 Under such circumstances, auxiliary requests 2 to 10 on application of Articles 12(2) and 13 RPBA are not admitted into the proceedings.

Request of remittal

10. The Board decided on the main request (patent as granted) and on the auxiliary request with regard to a ground of opposition (lack of inventive step) which was fully dealt with in the appealed decision and on the basis of the same documents (D1 and D6) as used in such a decision.

10.1 In this case the new arguments presented for the first time at the oral proceedings, although somewhat surprising, did not change the situation of the case to such an extent that the Board was not in the position of deciding on the issue, as can be seen from the reasons regarding lack of inventive step, which take full account both of the arguments of the appellant provided with the statement of grounds and of the new line of argumentation provided at the oral proceedings (see points 5 to 7, above). This is also why the question of admissibility of this new argumentation, which could have brought forward an alternative case, did not arise (as was the case e.g. in T 1621/09, cited under point 3.4, above, see points 2 to 37 of the reasons of that decision, in particular the conclusion in point 37(a)).

10.2 Under such circumstances, the Board does not see any reason which could justify a remittal of the case to the first instance (Article 111(1) EPC). The request of remittal of the appellant is therefore refused.

Conclusion

11. Since claim 1 according to all the admissible requests on file does not involve an inventive step, there is no need for the Board to decide on any other point and the appeal is dismissed.