T 0034/02 17-06-2005

1. Admissibility of opposition of opponent 01

1.1 The proprietor (appellant 02) challenged the admissibility of the opposition of opponent 01, an issue which, according to its opinion, had not been properly addressed by the opposition division. However, the proprietor (appellant 02) did not formulate a request in this respect. Nevertheless, the board has examined this issue ex officio.

1.2 With regard to the admissibility of the opposition of opponent 01, the objection of the proprietor (appellant 02) appears to have two aspects, namely

- inadmissibility of the opposition of opponent 01 as a whole because the grounds of Article 100(a) EPC have not been sufficiently substantiated as required by Rule 55(c) EPC;

- inadmissibility of the grounds of Article 100(a) EPC raised by opponent 01 because these grounds have not been sufficiently substantiated.

1.2.1 The opposition of opponent 01 was based on the grounds of Article 100(a) and 100(b) EPC (point II, above). The proprietor (appellant 02) has apparently accepted that the ground of Article 100(b) EPC had been sufficiently substantiated by opponent 01 in the notice of opposition. The board is also of the opinion that the ground of Article 100(b) EPC was sufficiently substantiated. Thus, a possible insufficient substantiation with regard to other grounds of opposition, in the present case with regard to the grounds of Article 100(a) EPC, cannot cause an inadmissibility of the opposition as a whole (see eg T 1029/01 of 22 May 2003, not published in the OJ EPO; point 2 of the reasons). Consequently, the proprietor's (appellant 02) first attack cannot succeed.

1.2.2 In the present case, not only opponent 01 but also opponent 02 based its opposition on the grounds of Article 100(a) EPC, namely lack of novelty and lack of inventive step (point II, above). Opponent 02 properly supported these grounds which has never been disputed by the proprietor (appellant 02). Consequently, the grounds of Article 100(a) EPC are in any case part of the factual and legal framework of the present opposition and opposition appeal proceedings and it is unnecessary for the board to rule on the second issue raised by the proprietor (appellant 02), ie as to whether or not opponent 01 properly supported the grounds of Article 100(a) EPC.

1.3 It follows from the above that the opposition of opponent 01 is admissible.

2. Admissibility of the appeals

The appeals of opponent 01 (appellant 01) and of the proprietor (appellant 02) comply with Articles 106 to 108 EPC and Rule 64 EPC and are therefore admissible.

3. Late filed ground of opposition (Article 100(c) EPC)

3.1 Opponent 01 (appellant 01) argued for the first time in the oral proceedings before the board that the granted patent extended beyond the application as filed and requested that the patent also be revoked in view Article 100(c) EPC therewith raising a new ground of opposition.

3.2 The introduction of new grounds of opposition is governed by G 9/91 (OJ 1993, 408, points 16 and 18 of the reasons) and G 10/91 (OJ 1993, 420, point 3 of the headnote) where it is held that fresh grounds of opposition may be considered in appeal proceedings only with the approval of the proprietor of the patent.

3.3 In the present case, the board could not ask for such an approval because the proprietor was not present at the oral proceedings (point X, above) where the new ground of opposition was raised for the first time. To continue the proceedings in writing in order to ask the proprietor (appellant 02) for such an approval was not considered by the board as an appropriate alternative. For a party to wait until oral proceedings before presenting the new ground of opposition that could have been presented earlier (the new ground of opposition was raised more than six years (!) after filing the opposition) de facto amounts to an abuse of procedure (in analogy to G 4/92 (OJ EPO 1994, 149; point 7 of the reasons).

3.4 Consequently, the board rejected the request of opponent 01 (appellant 01) to introduce Article 100(c) EPC as a new ground of opposition into the proceedings in accordance with Article 114(2) EPC.

Main request

4. Sufficiency of disclosure

4.1 Claim 1 as granted refers to a composition comprising a liquid system which contains an aqueous liquid medium including 0.05 to 20 wt% of detergent and a thickening mixture of two polymer types in an amount of from 0.01 to 5% by weight with respect to the liquid system. Furthermore, Claim 1 specifies the chemical nature of these two polymer types, namely a specific gum-type polymer and a specific acrylic-type polymer, and the amount of each polymer type, whereby the amount is defined on the one hand by the weight ratio of gum-type polymer to acrylic-type polymer and on the other hand in functional terms via a relationship between concentration and viscosity of each polymer. The latter requirement is defined as follows:

"... wherein each said polymer, when in the liquid medium in the absence of the other said polymer, has a relationship between concentration and viscosity, measured at a shear rate of 10 sec-1 and a temperature of 25°C such that a graph of log (viscosity) against log (concentration) is a sigmoid curve having a portion where, over a range of concentration the gradient of the curve of log (viscosity) against log (concentration) is constant or increases with log (concentration), and the amount of each of the said polymers is such that the concentration thereof in the liquid medium lies within the said range over which the gradient of the polymer's said curve of log (viscosity) against log (concentration) is constant or increasing, ...".

4.2 The arguments put forward by opponent 01 (appellant 01) against sufficiency of disclosure were directed to this functional definition of the amount for each polymer, namely that the determination of the sigmoid curve as described in Claim 1 was inconsistent with the teaching given in the patent specification and that the patent in suit failed to disclose a technical concept ("Lehre für ein zielgerichtetes Vorgehen") for finding the appropriate amount for each polymer.

4.3 According to opponent 01 (appellant 01), the wording in Claim 1 that "each said polymer, when in the liquid medium (emphasis added) ... has a relationship between concentration and viscosity ... such that a graph of log (viscosity) against log (concentration) is a sigmoid curve" means that the sigmoid curves of the polymers have to be measured in the liquid medium only, eg in water only.

4.3.1 This interpretation of opponent 01 (appellant 01) not only ignores the fact that the passage relied upon does not read "in the liquid medium only", it also ignores that Claim 1 requires already in line 1 that the liquid medium includes 0.05 to 20 wt% of a detergent. The attribution of the detergent to the liquid medium seems to suggest that the term "liquid medium" as used in Claim 1 is not only directed to a liquid as such, eg water, but also to the liquid including further ingredients.

4.3.2 Thus, if anything, Claim 1 raises doubts as to how the sigmoid curve of each polymer has to be determined, ie either in the liquid medium only, as alleged by opponent 01 (appellant 01), or in the liquid medium including detergents and, possibly, other ingredients present in the liquid medium. The quoted wording of Claim 1 ("each said polymer, when in the liquid medium ... ") would therefore be examined carefully by the person skilled in the art, using the description and the drawings when deciding how the sigmoid curves referred to in Claim 1 are to be determined.

4.3.3 At page 3, lines 53 to 55 of the patent in suit, it is stated that the sigmoid curves have to be measured "in the presence of any other ingredients which might be present in the liquid medium" (emphasis added). Furthermore, the patent in suit teaches at page 4, lines 9 to 18 that the sigmoid curve of Carbopol® 910 can be influenced by the addition of 3% sodium chloride which is illustrated in Figure 7. This example demonstrates how an unsuitable system can be "tailored" to become a suitable one. This implies that the sigmoid curve of the polymer is measured both with and without sodium chloride. Otherwise one would not observe a change in the behaviour of the sigmoid curve.

4.3.4 If, however, the relevant wording of Claim 1 were to be interpreted as proposed by opponent 01 (appellant 01), then it would not be consistent with the patent taken as a whole. Therefore, the skilled person trying, with synthetical propensity ie building up rather than tearing down (see T 190/99 of 6 March 200; point 2.4 of the reasons), to arrive at an interpretation of the relevant passage of Claim 1 which is technically sensible and takes into account the whole disclosure of the patent (Article 69 EPC) would rule out the interpretation of opponent 01 (appellant 01).

4.3.5 The only criticism that arises against Claim 1 goes to the rather careless use of the terms "liquid system" and "liquid medium" whose meanings appear to overlap. In fact, the terms may even be used synonymously. However, this is purely an issue under Article 84 EPC which is not a ground of opposition.

4.3.6 Hence, the board finds that there is no discrepancy between Claim 1 as granted and the patent specification which could lead to difficulties with respect to the implementation of the invention. Moreover, the contested claim, on its proper interpretation, is fully supported by the patent specification.

4.4 According to opponent 01 (appellant 01) the patent in suit fails to disclose a technical concept for finding the appropriate amount for each polymer. Moreover, a person skilled in the art is forced to use trial and error in order to find a polymer combination (nature of polymers and amounts thereof) which provides the promised synergistic effect resulting in an undue burden. In this context, opponent 01 (appellant 01) referred to T 435/91 (supra) and to Figure 7 of the patent in suit.

4.4.1 There is no dispute that every polymer will have a sigmoid curve in a particular liquid medium (including possible further ingredients) - the sigmoid curve is simply a graph indicating how the viscosity of the polymer in question varies with increasing concentration in the particular liquid medium (in the absence of the other thickening polymer). The measurement of viscosity will involve making up a number of solutions which vary in the concentration of one polymer and measuring viscosity. This is a straightforward process of measuring one property, namely viscosity, while altering one independent variable, namely concentration. Of course, someone carrying out this measurement of viscosity at varying concentrations can take guidance from the patent in suit as to likely ranges of concentrations to prepare for measurement of viscosity. Furthermore, the patent in suit explains the various portions of a sigmoid curve (page 3, lines 41 to 44; Figure 1) and provides guidance for those cases where the shape of the sigmoid curve may be non-ideal (page 3, lines 44 to 52).

4.4.2 After deriving this graph for both polymers, the skilled person has to select the amount of each polymer so that it lies on the portion of the sigmoid curve where the gradient is constant or increasing in order to obtain a synergistic thickening of the composition. This means that the overall thickening is not merely the predicted sum of the two viscosities but is unexpectedly greater. If the same polymers are used at even higher concentration, there would still be thickening. Indeed there might be greater thickening, but the extent of thickening would no longer be unexpectedly greater than predicted, and a greater quantity of polymer would be used.

This is illustrated in Example 1 of the patent in suit where the gum-type polymer is a xanthan gum designated Shellflo-XA and the acrylic polymer is designated PPE 1042. As can be seen from the table bridging pages 5 and 6, 0.2% of Shellflo-XA in the absence of PPE 1042 give a viscosity of 206 mPas at 10 sec-1. 0.5% of PPE 1042 in the absence of Shellflo-XA give a viscosity of only 24 mPas at 10 sec-1. It would be predicted that by using the two together the viscosity would be about 230 mPas. However, an unexpected greater viscosity of 420 mPas is observed.

Examples 2 and 3 are a very clear illustration of the fact that the range of concentration at which this unexpected synergy is observed is dependent on the choice of polymer. Example 2 uses 0.1% of xanthan gum (Shellflo-XA) with varying amounts of Carbopol® 940 as the acrylic-type polymer. Example 3 uses the same concentration of Shellflo-XA but uses Viscalex HV 30 as the acrylic-type polymer. In Example 2 it is shown that when the quantity of Carbopol® 940 is 0.07% or less the overall viscosity is greater than would be expected by simple linear addition of the viscosities. This unexpected synergy is at a maximum when the concentration of Carbopol® 940 is about 0.04% and is declining almost to vanishing point when the concentration of Carbopol® 940 is 0.08%. By contrast with Viscalex HV 30, the effect is small at 0.1% and is at its maximum at a concentration of 0.3% before falling away at even higher concentration.

4.4.3 Thus, contrary to the assertion of opponent 01 (appellant 01) the patent in suit provides a technical concept for finding the appropriate amount for each polymer and clear guidance for the implementation of this concept. Moreover, in view of the variation from one polymer to the other (see Examples 2 and 3) the functional definition in terms of the shape of the sigmoid curve is justified. It may be tedious to establish the graphs for the polymers a skilled person may want to use, in particular because all ingredients present in the liquid medium have to be taken into account, but no undue difficulties arise when establishing these graphs.

4.4.4 Opponent 01 (appellant 01) made reference to T 435/91 (supra), a case where one of the essential components was only defined by its function (an additive which forces a detergent composition into hexagonal liquid crystal phase). According to this decision, the requirements of Article 83 EPC are not met if the patent discloses only isolated examples but fails to disclose any technical concept fit for generalisation, which would enable the skilled person to achieve the envisaged result without undue difficulty within the whole ambit of the claim containing the functional definition (headnote, point 2.2.1 of the reasons).

However, the present case differs from T 435/91 (supra) because the patent in suit provides technical information as to how to obtain, with a reasonable expectation of success, the appropriate amount of thickening polymers. In fact, this information is, as pointed out in section 4.4.2, above, a fully self- sufficient technical concept as to how the appropriate amount is to be obtained, namely selecting the amount of each polymer so that it lies on the portion of the sigmoid curve where the gradient is constant or increasing.

4.4.5 Opponent 01 (appellant 01) also referred to Figure 7 of the patent in suit which shows the variation in synergy for a 0.1% Shellflo XA solution with various concentrations of Carbopol® 910 in the absence and in the presence of 3% sodium chloride. According to opponent 01 (appellant 01), the fact that this combination of thickening agents shows in the absence of sodium chloride no synergy at all is evidence for the lack of concept in the patent in suit. However, opponent 01 (appellant 01) seems to overlook that Figure 7 shows synergy at a very low concentration of Carbopol® 910. It appears from Figure 6, the sigmoid curve for Carbopol® 910, that the gradient of the sigmoid curve at this low concentration is constant, therefore one would expect synergy. Furthermore, the comments of opponent 01 (appellant 01) concerning Figure 7 seem to overlook the explanation of that figure which is given on page 4, lines 9 to 18 of the patent in suit. According to this passage, a mixture of 0.1% Shellflo XA and 0.2% Carbopol® 910 in aqueous dispersion at pH 9.5 gives a synergistic increment of approximately -30%. It can be seen from Figure 6 that a concentration of 0.2% Carbopol® 910 is not in the required part of the sigmoid curve. That is, according to the proprietor (appellant 02), why there is no synergy. The purpose of Figure 7, as explained in the text, is to show that if someone wished to achieve synergy with 0.2% or anything from 0.1 to 0.5% Carbopol® 910, they would have the opportunity of increasing the electrolyte concentration, ie moving the sigmoid shape of the log (viscosity)/log (concentration) graph towards higher values of concentration of this polymer. Thus, whilst the explanation given in connection with Examples 1 to 3 shows how to put the invention into effect, the further explanation given in connection with Figures 6 and 7 is about how to put the invention into effect while accepting a restriction on the choice of concentration of one polymer. Consequently, Figure 7 cannot invalidate the technical concept as presented in the patent in suit.

4.4.6 Hence, the board finds that the patent in suit discloses a technical concept fit for generalisation which enables the skilled person to achieve the envisaged result as regards the functional definition of the amounts of the polymers without undue difficulty.

4.5 It follows form the above, that the requirements of Article 83 EPC are met.

5. Novelty

It may be convenient to recall at this juncture that D2 and D7 are the only documents relied upon by opponent 01 (appellant 01) for novelty (see section X, above). The opposition division has relied only on the latter document to refuse Claim 1 as granted in view of Article 54 EPC.

5.1 Document D7

5.1.1 D7 claims in Claim 1 a liquid cleansing product comprising from 5 to 30% surfactant, from 0.1 to 1.0% guar material selected from guar gum and guar gum derivatives, from 0.15 to 1.0% of carboxyvinyl polymer, and water. The products provide beneficial skin feel properties. D7 has five examples which disclose cleansing products comprising surfactants and a combination of two thickening polymers, namely Carbopol® 934 in combination with various types of Jaguar components (Jaguar HP-60, Jaguar HP-11 and Jaguar-A-40-F). Carbopol® 934 is an acrylic type polymer according to Claim 1 of the patent in suit, and the Jaguar components are all gum-type polymers according to Claim 1. The range of amounts of Carbopol® 934 (0.25 to 0.35%) and Jaguar gums (0.30 to 0.60%) in the examples is narrower than the full range claimed in D7. It is conspicuous to the board that there is no disclosure of a composition in D7 with amounts of either polymer being below 0.25%.

5.1.2 It has never been shown for a composition disclosed in D7, either in the opposition or in the opposition appeal proceedings, that the concentrations of both polymers would lie on the required portion of the sigmoid curves for those polymers. Since, however, the onus of proof in this respect lies with the opponents (T 219/83, OJ EPO 1986, 211), the novelty objection based on D7 must fail.

5.1.3 In this connection it should be noted that the only evidence that has been submitted to the EPO regarding the disclosure of D7 was the experimental evidence D10 provided by the proprietor (appellant 02). In following Example 1 of D7, the proprietor (appellant 02) has shown that the gradient of the graph log(viscosity) against log(concentration) is decreasing when the concentration of Jaguar HP-60 reaches 0.3 wt.%. Accordingly, the composition of Example 1 of D7 falls outside the scope of Claim 1 as granted.

5.1.4 Furthermore, it appears from the decision under appeal (point 4), that the opposition division combined a specific example, ie Example 3, with the lower limits of the two ranges given in Claim 1 for the thickening polymers (0.1% guar material and 0.15% carboxyvinyl polymer) in order to create a novelty destroying embodiment. However, this approach cannot succeed because such a combination is the result from a multiple selection from the disclosure of D7 which does not emerge from D7 as being implicitly disclosed for the skilled person (eg T 453/87 of 18 May 1989; not published in the OJ EPO; point 7.2 of the reasons). Apart from this there is no evidence on file that this "artificial" embodiment would meet the requirements of Claim 1 as granted.

5.1.5 For the above reasons, the board concludes that the subject-matter of Claim 1 of the patent in suit is novel over the disclosure of D7.

5.2 Document D2

5.2.1 D2 relates to a method for cleaning teeth and a dental preparation to be used therewith which comprises two components, a first component containing hydrogen peroxide and a second component containing sodium bicarbonate as an active ingredient (Claim 1). According to Claim 11, the first component is a gel comprising as a gelling agent a member selected from the group consisting of (a) copolymers of acrylic acid cross-linked with polyallyl sucrose, (b) an organic polymeric acid colloid, and (c) a polyoxyethylene/ polyoxypropylene block copolymer.

According to the disclosure in column 3, lines 31 to 51, the most preferred gelling agents are stated to be those marketed by the company Goodrich under the trademark Carbopol 941, 1342, 934 and 940 which correspond to the acrylic-type polymers of Claim 1 of the patent in suit. The synthetic cross-linked acrylate polymer can be used in combination with a suitable amount of non-ionic cellulose gum such as hydroxyethyl or hydroxypropyl cellulose or hydroxypropyl methylcellulose (column 3, lines 23 to 29) which are gum-type polymers as referred to in Claim 1 of the patent in suit.

In addition to this general disclosure, Examples 4, 6 and 10 of D2 disclose compositions comprising a liquid system which contains an aqueous liquid medium, a detergent and a mixture of Carbopol® 934 and hydroxypropyl cellulose (Examples 4 and 10) and hydroxypropyl methylcellulose (Example 6), respectively.

5.2.2 Although the burden of proof lies on the opponents (see section 5.1.2, above), they have never demonstrated that the concentrations of the two thickening polymers used in the examples of D2 would lie on the required portion of the sigmoid curves for these polymers. Also at the oral proceedings before the board where opponent 01 (appellant 01) relied on D2 as a novelty destroying document, no such evidence was provided.

5.2.3 Hence, the board concludes that the subject-matter of Claim 1 is novel over D2.

5.3 It follows, in view of the above, that the subject- matter of Claim 1 as granted and, by the same token, the subject-matter of Claims 2 to 14 as granted, is novel over D7 and D2.

6. Problem and solution

6.1 The prior art considered during the examination proceedings is discussed in the introductory part of the patent specification. From this discussion, it can be taken that polymeric thickening agents such as polysaccharide hydrocolloids and polymers which include acrylate homo- and copolymers and derivatives thereof were well known. It is discussed furthermore that it was known in the field of polymeric thickening agents that, in general, the viscosity of a liquid is dependent on the concentration of thickening agent in that liquid (page 2, lines 38 to 39 of the patent specification). Also the combined use of crosslinked acrylic-type polymers and gum-type polymers being polysaccharides is known (cf the discussion of D2 on page 3, lines 8 to 10 of the patent specification).

Thickening agents are used in many areas of industry to impart a certain rheological behaviour to liquid media. Thus, the patent in suit specifically refers to compositions in the form of a toothpaste (Claim 13) or in the form of a shampoo, shower and bath gel (Claim 14).

6.2 D2 uses a mixture of thickening agents in dental preparations (section 5.2.1, above). Thus, apart from using the same types of polymer thickeners, namely gum- type and acrylic-type polymers, the compositions of D2 serve a similar purpose as the compositions of the patent in suit, in particular those referred to in granted Claim 13. Hence, the board accepts that D2 represents the closest prior art, as submitted by opponent 01 (appellant 01).

6.2.1 As explained in section 4.4.2, above, the data in the patent in suit show that if crosslinked acrylic-type polymer was used jointly with a gum-type polymer and if the concentration of both polymers was selected so that for the individual polymers the concentration lies on the part of the sigmoid curve where the gradient is constant or rising, the overall thickening is not merely the predicted sum of the two viscosities but was unexpectedly greater. Thus, the patent in suit goes beyond the mere provision of an effective mixture of thickening agents, it aims at the optimization of a particular mixture already known in the prior art, namely a mixture of a specific gum-type polymer and a specific acrylic type polymer.

6.2.2 Therefore, the objective technical problem to be solved by the patent in suit has to be seen in the optimization of a thickening mixture of a gum-type polymer and an acrylic type polymer with respect to its thickening efficiency, ie a balance between the extent of thickening and the amount of thickening agents used. In this connection, the patent in suit uses the term "synergistic effect" (eg page 2, lines 3 to 4 of the patent in suit).

6.3 The solution proposed by the patent in suit is to select the concentration of both of these polymers so that for the individual polymers the concentration lies on the part of the sigmoid curve where the gradient is constant or increasing. In view of the experimental evidence in the patent in suit, in particular with respect to Examples 1 to 3 (see section 4.4.2, above), the board has no reason to doubt that the claimed measures provide an effective solution to the stated problem.

7. Inventive step

7.1 For the assessment of inventive step, it is necessary to consider whether the skilled person, in possession of the technical teaching according to D2, would have expected that the thickening efficiency of a mixture of a gum-type polymer and an acrylic-type polymer could be enhanced by choosing specific amounts of the individual components.

7.2 In D2 itself, there is no suggestion as to how the thickening properties of a mixture a gum-type polymer and an acrylic-type polymer might be further improved, let alone a hint as to select the amounts with respect to the log (viscosity)/log (concentration) graph. Consequently, the disclosure of D2 itself offers no hint to the solution of the relevant technical problem.

7.3 At the oral proceedings before the board, opponent 01 (appellant 01) argued that D6 provided a hint that the combination of a gum-type thickener and an acrylic-type thickener provides a synergistic effect.

7.3.1 D6 discloses thickeners made by blending an alkaline wet gum with a polymeric polyacid whereby the product has a matrix of gum thickener. The gum thickeners used are polysaccharides (page 2, lines 19 to 38). Preferred polymeric polyacids are - inter alia - polyacrylic acids copolymerised with a minor amount of a polyallyl ether of a polyol marketed under the trade mark "Carbopol" (page 3, lines 15 to 19). The product, after being dried and ground, is soluble in water, can be processed in conventional equipment, shows a stronger thickening capacity than unmodified natural products and is therefore usable in smaller amounts (page 2, lines 14 to 18). In the textile industry, for example, excellent printing results are achieved due to the reduced amount of thickener (page 5, lines 1 to 8).

7.3.2 Thus, D6 teaches that a mixture of gum-type polymer and acrylic-type polymer is a more effective thickener than prior art thickeners whereby the presence of a detergent, a mandatory feature of granted Claim 1, is not mentioned at all. However, the technical problem as defined in section 6.2.2, above, goes beyond the mere provision of an effective thickener combination, it goes to the optimization of the thickening efficiency of a combination of gum-type thickener and acrylic-type thickener. And to this aspect, D6 does not provide any information at all. Consequently, D6 cannot provide a suggestion as to the solution offered by the patent in suit, either on its own or in combination with D2.

7.4 The same arguments as to D6 apply also to D5 briefly referred to by opponent 01 (appellant 01) at the oral proceedings before the board. D5 discloses a thickener consisting of xanthan gum and a water soluble salt of an acrylic acid polymer but there is no hint as to the optimization of the thickening efficiency of the disclosed mixture. In addition, the presence of a detergent is not mentioned.

7.5 The argument of opponent 01 (appellant 01) submitted at the oral proceedings that the skilled person would, in view of the common general knowledge (ie higher increase in thickening at lower thickener concentrations), work at low thickener concentrations is not convincing. As can be seen from Example 2 (section 4.4.2, above), working at low concentrations does not necessarily lead to an optimization in thickening efficiency. At a concentration of 0.08% Carbopol® 940, ie at a rather low concentration, the synergy is declining almost to vanishing point. It appears therefore that the argument of opponent 01 (appellant 01) is based on hindsight since without the knowledge of the teaching of the patent in suit a skilled person had no incentive whatsoever to focus on particular amounts of gum-type thickener and acrylic type thickener.

7.6 The fact that the teaching of the patent goes beyond the teaching of D2 and/or D6 defeats also the argument of opponent 01 (appellant 01) that the claimed subject- matter is a mere explanation of a known effect. Consequently, T 892/94 (supra) relied upon in this connection is not applicable to the present case.

7.7 In view of the above, it is evident that the subject- matter of Claim 1 as granted and, by the same token, the subject-matter of Claims 2 to 14 as granted, does not arise in an obvious way from documents D2 and D6 and/or D5. Hence the subject-matter of Claims 1 to 14 as granted involves an inventive step (Article 56 EPC).

8. Because the proprietor (appellant 02) succeeded on the main request, there was no need to consider its auxiliary requests.